Continuing from my earlier post about iptables basics, the limit module of iptables can be used to mitigate DoS (Denial of Service) attack. Note that mitigating here means “reducing the damage”. The worst scenario is under a heavy DoS you can’t even SSH and run commands on your server. With iptables you can limit the frequency of packets — enabling you to SSH and take appropriate actions.
Following are the rules I currently use. This will only allow new incoming TCP connection on port 80 & 443 with specified frequency (see limit explanation below):
iptables -A INPUT -j ACCEPT -p tcp --dport 80 -m state --state NEW -m limit --limit 40/s --limit-burst 5 -m comment --comment 'Allow incoming HTTP'
iptables -A INPUT -j ACCEPT -p tcp --dport 443 -m state --state NEW -m limit --limit 40/s --limit-burst 5 -m comment --comment 'Allow incoming HTTPS'
-
-A INPUT: Append to the end of a chain called INPUT
-
-j ACCEPT: When rule match, accept the packet
-
-p tcp: Match only TCP protocol
-
–dport: Match given TCP port
-
-m state: Use the state module
-
–state NEW: Match only packets initiated from new connection. This rule will not match packets exchanged from an existing connections.
-
-m limit: Use the limit module
-
–limit 40/s: If more than 40 packet per second received, decrement one burst point. If no more burst point, reject the packet
-
–limit-burst 5: The initial number of burst point. A “burst” occur when the limit above is reached. On a period where limit is not reached, one burst point is regained, up to this maximum limit. If burst point is 0, subsequent burst will cause the current rule matching to fail — and iptables will try the next rules (if you setup iptables properly the packet should slip through to ‘reject all’ rule)
Add following rule to allow your program making connection to localhost (loopback interface)
iptables -A INPUT -i lo -j ACCEPT
I then append a rule to match packets exchanged from established / related connections. This is important so packet resulted from outbound connections are accepted:
iptables -A INPUT -j ACCEPT -m state --state RELATED,ESTABLISHED -m limit --limit 100/s --limit-burst 50
And finally, reject all packets not accepted by above rules. Be careful before you do this, make sure you’ve added rules to allow SSH (port 22) so you don’t lock yourself out.
iptables -A INPUT -j REJECT
Testing And Continual Adjustment
Finding the correct number for limit and burst could be hard, but what I find useful is to perform continuous monitoring and adjustment. Keep in mind your goal here is to ensure maximum capacity of the server is utilised while protecting it against DoS. One approach I like is to use the iptables LOG target. Assuming I add following rules:
iptables -A INPUT -j ACCEPT -p tcp --dport 80 -m state --state NEW -m limit --limit 40/s --limit-burst 5
iptables -A INPUT -j LOG -p tcp --dport 80 -m state --state NEW --log-prefix 'TCP 80 Burst Exhausted'
If the first rule did not match (eg: because of burst is exhausted), the LOG rule after it will match and print into your syslog (typically /var/log/messages) with prefix “TCP 80 Burst Exhausted”. LOG target will not accept / reject the packet — after logging, iptables will continue checking the subsequent ruless.
The neat thing here is you can grep ‘TCP 80 Burst Exhausted’ /var/log/messages to detect when was last time suspected DoS attack occured. If the suspected attack is determined to be false alarm, your limit and burse setting is too strict, and you should gradually increase it.
Saving and Restoring
Updating rules at specific order can be very tedious, you have to count the terminal screen lines, insert the new rule, delete the old one and so on. There’s one trick you can do, that is to leverage iptables-restore command. Everytime you save the rule using service iptables save /etc/sysconfig/iptables file is updated with your rule specification. You can update this file and restore it using iptables-restore. Beware! A syntax error will cause your rule to be skipped. It’s best to test your command first by adding it to the bottom, and use this method to re-order the rules.
